A Shepherd company - serving Summerlin, NV

GAF Flashing Replacement in Summerlin, NV

Architectural shinglesArchitectural shingles
Metal roofingMetal roofing
Tile roofingTile roofing
GAFGAF
Owens CorningOwens Corning
Flat & low-slopeFlat & low-slope
Every visit starts with

Free roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation

We have financing partners for your new roof*On approved credit; ask us about your options
Get your free estimate

GAF Flashing Replacement: The Summerlin Owner’s Guide

GAF-compatible flashing replacement in Summerlin typically runs $275 to $650 installed per section, and most single-section jobs are finished in a day once the right part is on site. Flashing is the metal that seals the joints where your roof meets walls, chimneys, valleys, and vents, and it’s the first thing water attacks when it lets go. Owners around Summerlin usually find out the hard way: a brown ring on the ceiling below a wall line, grit-colored stains on stucco, or a roofer pointing at lifted step flashing during a routine inspection. We install GAF-compatible flashing to match what’s already on your roof, and we’ll show you the deck photos before we talk money.

Call (844) 951-4545

Which GAF Models This Applies To

GAF flashing isn’t a single product; it’s a family of components sized to the roof system. Step flashing and counterflashing pair with GAF’s Timberline HDZ and UHDZ shingle lines, while the company’s roof-to-wall and valley metal show up across its residential systems. If you’re matching existing work, the shingle wrapper tells you a lot: find the bundle label or the stamp on a spare course and note the series, then measure the exposed reveal on your step flashing (commonly about 4 to 5 inches) before ordering anything. Here’s the gotcha most homeowners miss: GAF specifies its own flashing profiles and lap details for warranty-covered installs, so a generic hardware-store angle that “fits” can void coverage on the surrounding shingles even though it looks fine. We’re an independent contractor and not affiliated with GAF, but we set GAF systems regularly and we’ll match OEM-profile flashing when the roof calls for it, or a quality aftermarket equivalent when the geometry and budget make more sense. Ask us which one we’re using and why before we start.

Explore

Styles & brands we work with

  • Architectural shingles
  • Metal roofing
  • Tile roofing
  • GAF
  • Owens Corning
  • Flat & low-slope

Signs Your GAF Flashing Replacement Is Failing

  • Rust streaks or pitting on the metal. Summerlin’s dry heat and monsoon swings push steel through expansion and contraction cycles, and once the galvanized coating breaks, corrosion follows fast. The metal looks intact from the ground but is thinning at the bends.
  • Water stains on the ceiling or wall below a joint. This means water is already past the flashing and into the sheathing. Caught early it’s a flashing swap; caught late it’s decking too.
  • Lifted, curled, or separated step flashing. Wind gets under an edge, the metal tents up, and the shingle above no longer laps it correctly. That gap is where the next storm gets in.
  • Cracked or crumbling sealant along the counterflashing. Old caulk fails before the metal does, and a bead that’s split lets water behind the flashing instead of over it.
  • Gaps where the roof meets a wall, chimney, or skylight. If you can see daylight or slide a putty knife into the seam, the flashing has pulled loose from the substrate. That’s a repair decision, not a wait-and-see.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

In Summerlin, single-section flashing replacement runs about $275 to $650 installed. Chimney flashing and valley work sit at the higher end because there’s more metal, more cutting, and more careful weaving. Long runs along a wall, two-story access, and tile or steep-slope roofs push the number up; simple step flashing on a low-slope section sits lower. What drives the range: linear feet of metal, roof pitch and access, whether the decking underneath is sound, and whether we’re matching an OEM GAF profile or a standard equivalent. The price includes tear-off of the old flashing, new metal, sealant, and re-lapping the shingles so the joint is watertight again. Repair work over $200 knocks $40 off, no trip charge inside our own county, and every job carries our written 90-Day Done Right Promise. Estimates are free, and a second opinion on any written bid costs you nothing.

DIY or Call Us?

You can safely walk the roof from the ground with binoculars, check the ceiling inside for stains after a storm, and look for rust or lifted metal at your wall and chimney joints. That’s the extent of the safe checking. Flashing replacement means pulling shingles, lifting metal that’s often sharp, working at height on a slope, and re-lapping everything to shed water correctly, and a mistake there shows up months later as rot in the decking. On a two-story or steep roof, this isn’t a weekend job. One call to (844) 951-4545 brings Bill out to look at it, and he’ll tell you straight whether it’s a swap or something bigger.

FAQs

Need Roofing help nationwide? Licensed & insured · free written estimates
Call (844) 951-4545
Local Service Coverage

Request a Free Estimate in Summerlin

Tell us what you need - Shepherd & Sons Roofing Summerlin responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch