A Shepherd company - serving Summerlin, NV

Owens Corning Flashing Replacement in Summerlin, NV

Owens CorningOwens Corning
Architectural shinglesArchitectural shingles
Metal roofingMetal roofing
Tile roofingTile roofing
GAFGAF
Flat & low-slopeFlat & low-slope
Every visit starts with

Free roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation

We have financing partners for your new roof*On approved credit; ask us about your options
Get your free estimate

Owens Corning Flashing Replacement: The Summerlin Owner’s Guide

Flashing replacement for Owens Corning roof systems in Summerlin typically runs $280 to $600 installed per section, depending on where it sits and how much decking needs repair underneath. We install Owens Corning-compatible flashing and counterflashing, match the profile to your existing shingle or low-slope membrane, and most jobs are done in a single visit. We’re an independent roofing contractor and not affiliated with Owens Corning itself.

Call (844) 951-4545

Owners usually find out the flashing failed the same way every time: a brown water stain on the ceiling sheetrock a foot in from the exterior wall, or a dark streak down the stucco after a monsoon dump in July or August. Sometimes it’s a roofer who pointed at a rusted drip edge while chasing a leak somewhere else. Either way, the part is small, the damage it does is not, and Summerlin’s sun-baked-then-soaked cycle is hard on these components.

Which Owens Corning Models This Applies To

Owens Corning roofing covers several product families, and flashing compatibility tracks the roof type more than the shingle itself. On the asphalt side that’s Duration and Oakridge shingles, plus the low-slope and tile-and-metal trim lines. Flashing on those roofs is usually the metal step flashing, counterflashing, drip edge, and valley metal that interface with the shingle course, and the right replacement profile depends on shingle thickness and the reveal you’re running. Duration is a heavier, thicker shingle than Oakridge, so a drip edge or step flashing that fits one may sit proud or under-supported on the other. We check the existing profile, measure the exposed shingle height, and match it.

Identifying your roof is straightforward. The Owens Corning label is usually stapled inside an attic rafter or stuck to a deck panel. If it’s gone, we count shingle tabs, measure the exposed height, and check the cap style. Once we know the shingle family, the flashing profile follows. OEM flashing is worth it where the profile is a tight fit to the shingle system; a quality aftermarket piece in the right gauge is fine where the metal is structural or generic, like standard drip edge. What matters more than the label is gauge, coating, and whether the seams and nailing pattern will hold through a Summerlin wind event.

Explore

Styles & brands we work with

  • Architectural shingles
  • Metal roofing
  • Tile roofing
  • GAF
  • Owens Corning
  • Flat & low-slope

Signs Your Owens Corning Flashing Replacement Is Failing

  • Rust streaks or orange staining on the stucco or fascia. The protective coating has broken down, and the metal is oxidizing. In Summerlin, galvanized steel that isn’t coated well pits fast under the UV load.
  • Water stains on interior walls near the perimeter. Step flashing has lifted or pulled away from the shingle course, and wind-driven rain is tracking behind it. This is the classic first leak signature, not a shingle failure.
  • Caulk peeling or gaps along the flashing-to-wall joint. Someone sealed a seam that should have been lapped and mechanically fixed. Caulk fails in a couple Nevada summers, and the gap grows.
  • Drip edge pulled away from the fascia or bent up. Nails have backed out or the metal was undersized for the deck overhang. Water then wicks back under the edge instead of shedding clear.
  • Granule loss or shingle wear concentrated at the flashing lines. Repeated moisture at the interface softens the deck and shingle mat. The flashing is the tell, but the shingle edge and deck may be involved too.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Here’s the honest range for Summerlin. A straightforward step-flashing or drip-edge section replacement runs $280 to $420 installed. Counterflashing at a wall or chimney, which involves getting behind the siding or stucco and re-sealing correctly, runs $380 to $600. If the deck underneath is soft and needs a patch, add $150 to $400 depending on square footage and whether we’re matching sheathing thickness.

What drives the number up is access: a two-story pitch, a tight spot next to a valley, or tile that has to be lifted and reset. What drives it down is doing a whole run at once instead of patching one section. We give you a written line-item quote before anyone touches the roof. The flashing labor and materials carry our 90-Day Done Right Promise in writing, on every job.

DIY or Call Us?

Some flashing work is genuinely dangerous to do yourself, and I’ll say it plainly: anything on a steep pitch, anything at a second-story wall line, and anything requiring you to peel back shingles and work in the roof’s water plane. A mistake there doesn’t just leak, it can let water into the sheathing for months before you see it. Beyond the safety part, the flashing itself is where DIY goes wrong most often. The lap direction has to be right, the metal has to sit under the shingle above and over the shingle below, and nailing through the wrong spot creates a hole you can’t see. What you can safely do is check for rust streaks and peek in the attic after rain. What you shouldn’t do is climb out on a two-story roof to caulk a seam you can’t fully reach. Call us at (844) 951-4545 and we’ll give you a straight answer and a free estimate.

FAQs

How long does Owens Corning flashing last in Summerlin? A well-installed flashing section lasts 20 years or more, but in Summerlin’s climate, unprotected galvanized metal often starts showing surface rust in 8 to 12 years because of the high UV and monsoon wetting. Coating choice matters more than brand here. Call (844) 951-4545 with your roof details for a free estimate.

Can the flashing be repaired instead of replaced? Sometimes, yes. A single pulled nail or a small lifted section can be re-seated and re-sealed. Once the metal is rusted through or the deck behind it is soft, replacement is the only fix that lasts. We’ll tell you which one you’re looking at. Call (844) 951-4545.

How long does the swap take? A single flashing section replacement is typically a half-day job. Counterflashing at a wall or chimney, or a longer run, is usually a full day. We’ll tell you before we start and don’t leave an opening exposed overnight. Call (844) 951-4545 to schedule.

How do you source the Owens Corning part? We match the profile to your shingle family (Duration, Oakridge, or the low-slope lines), measure the reveal, and source OEM or a spec-matched equivalent depending on what the joint actually needs. We don’t carry parts on a truck, so we order to the job and confirm the fit before the day of work. Call (844) 951-4545 for a free estimate.

Written by the team at Shepherd & Sons Roofing Summerlin, serving Summerlin and nearby areas.

Need Roofing help nationwide? Licensed & insured · free written estimates
Call (844) 951-4545
Local Service Coverage

Request a Free Estimate in Summerlin

Tell us what you need - Shepherd & Sons Roofing Summerlin responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch