Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Owens Corning Metal Roofing in Summerlin: What to Know First
We install and repair Owens Corning metal roofing in Summerlin as an independent Owens Corning service provider, and most residential metal roof jobs here run two to five days on site once materials land. Expect standing seam to start higher than corrugated or metal shingle, because the price follows the panel, the trim, and the number of penetrations, not the brand name on the wrapper. This page is for Summerlin homeowners who already own or are considering an Owens Corning metal roof and want a straight read on what fails, what it costs, and who’s actually doing the work. Call (844) 951-4545 and a live person picks up.
How Owens Corning Products Fail – and How We Fix Them
Metal roofing fails differently than asphalt, and Owens Corning metal systems are no exception. Here’s what we actually see on Summerlin roofs, and what we do about it.
- Fastener back-out and washer fatigue on standing seam panels. The concealed clips and fasteners that hold a standing seam panel are the part nobody sees and everybody forgets. Summerlin’s afternoon heat cycling – triple-digit summers, cool desert nights – works those fasteners loose over a decade or so, and once a clip backs out you get panel movement and a rattle before you ever get a leak. We pull a section, inspect the clips, and replace the failed hardware with the correct gauge and washer rather than running a screw through the panel and calling it fixed.
- Granule loss and chalky fade on metal shingle profiles. Owens Corning’s metal shingle lines carry a stone-coat finish, and the sun here punishes that finish. Chalky white streaks and bare patches on the south and west slopes are the first sign – and homeowners often blame the paint when the real cause is UV exposure combined with a panel that was installed tight against the deck with no ventilation gap underneath, so heat has nowhere to go. We check the underlayment and air gap first, because recoating a panel that’s cooking from below just buys you two more summers.
- Cut-edge rust on corrugated and exposed-fastener panels. Where a panel gets cut in the field, the bare steel edge is a rust start point. On Summerlin roofs we regularly see this at valleys and around chimney flashings, and it spreads under the paint film faster than owners expect. Our fix is to treat and seal the cut edge properly, not just touch it with a spray can, and to reflash with matching material.
- Dissimilar-metal corrosion at flashings and penetrations. An aluminum flashing married to a steel panel, or a galvanized nail in a copper valley, sets up a galvanic reaction that eats the connection from the inside. It’s a quiet failure and it shows up as a stain or a pinhole years later. We match metals correctly at every transition and isolate where we can’t.
- Sealant failure at penetrations and ridge caps. Pipe boots, vent stacks, and ridge cap sealant are the first things to go on any metal roof, Owens Corning included. Summerlin’s UV load cures standard sealant brittle in a handful of years. We replace failed boots and sealant with UV-rated material and check every penetration on the roof, not just the one that’s leaking.
One thing worth knowing that you won’t find on the manufacturer’s site: Owens Corning metal panels and trim are often shipped from regional distribution, so a field-cut piece can arrive with a slightly different dye lot than the rest of the roof. On a repair, that means the patch may read a shade off in direct sun even when the work is perfect. We tell you before we cut, and we order trim from the same lot when we can.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Our Owens Corning Metal Roofing Process
- 1
The call. You reach a live person, day or night. We ask what you’re seeing – a leak, a rattle, a stain, panels that look wavy – and set a time to come out.
- 2
Diagnostics on the roof. We get up there, photograph what we find, and show you the deck and the panels before we talk money. A roof is measured in squares – ask any bidder how many they counted, and we’ll tell you ours.
- 3
The parts decision. OEM Owens Corning trim and fasteners keep the system matched to the panel. Quality aftermarket hardware is sometimes the right call for a repair where OEM lead time is long, and we’ll tell you the trade-off in plain terms so you’re not guessing.
- 4
The work. Repairs get matched panels and correct fastening; full installs get underlayment, air gap, and flashing done to spec. The nailing pattern earns the wind rating, not the panel wrapper.
- 5
The test. We water-test the repair or walk the whole roof on a new install, and you get photos of the finished work.
- 6
The written promise. Every roofing job carries our 90-Day Done Right Promise in writing – if it’s not done right, one call brings Bill back.
See the difference
Before
After
Before
After
Before
AfterWhat Owens Corning Metal Roofing Costs in Summerlin
Here’s the honest range. Your number depends on roof size, panel type, pitch, and how many penetrations we’re flashing.
| Job | Typical range |
|---|---|
| Metal roof repair (fasteners, flashing, small patch) | $350 – $1,200 |
| Sealant and boot replacement at penetrations | $250 – $650 |
| Metal roof coating / refinish | $1.50 – $3.50 per sq ft |
| Corrugated or exposed-fastener metal install | $8 – $12 per sq ft |
| Standing seam metal install | $12 – $18 per sq ft |
| Metal shingle install | $10 – $16 per sq ft |
What moves the price: panel type, roof complexity and pitch, how much flashing and trim you need, and whether we’re tearing off an old roof first. Estimates are free, and a second opinion on any written estimate is free too. Call (844) 951-4545 for an exact number.
Why Summerlin Homeowners Call Shepherd & Sons Roofing Summerlin for Owens Corning Work
Same address since 1996. Ask the storm chasers where theirs is. We’ve been owner-operated and locally owned the whole time, and the name on the truck is the name on the license – published, look-it-up, no guessing who’s accountable. A live person answers the phone 24/7, not a call center. The crew is background-checked, and Bill’s own sons are on the roof with him. Our technicians have up to 30 years of experience on metal systems, and we install products from Owens Corning, GAF, and CertainTeed, so we’ve set the panel you’re asking about. Every job is backed by our written 90-Day Done Right Promise, and there’s no trip charge inside our own county. Call (844) 951-4545 to schedule your free estimate.
FAQs
Not if the repair is done to the manufacturer’s spec with matched components. We’re an independent Owens Corning service provider, not affiliated with or authorized by Owens Corning, so we handle the warranty-safe practices ourselves: correct fasteners, matched metals, and proper flashing. Ask us and we’ll walk you through what keeps your coverage intact. Call (844) 951-4545 for a free second opinion.
Usually, yes – same panel profile and color from regional distribution, and we order from the same lot when we can. The catch is dye-lot variation, so a patch may read slightly different in direct Summerlin sun. We’ll tell you before we cut.
Repair if the failure is localized – fasteners, sealant, a flashing, a single panel. Replace if you’re seeing widespread rust at cut edges, corrosion at many penetrations, or panels moving across the field. We show you the deck photos and give you the honest call.
For a genuine leak or storm damage we move quickly, and a live person answers the phone 24/7 including nights and weekends after a storm. Planned installs get scheduled around material delivery. Call (844) 951-4545 and we’ll set a time.
Yes. We also service GAF and CertainTeed roofs, along with several others, so you’re not stuck if your panel isn’t Owens Corning. Same process, same written promise.
Written by the team at Shepherd & Sons Roofing Summerlin, serving Summerlin and nearby areas.