Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
GAF Specialty Roofing in Summerlin: What to Know First
We provide independent GAF specialty roofing in Summerlin, and most jobs run two to four days of actual work once materials are on site. Pricing is upfront and written line-item: you see what’s being done and what it costs before anyone touches your roof. As an independent GAF service provider, we’re not affiliated with or authorized by GAF – we simply know their products well.
This page is for Summerlin homeowners with a GAF roof that needs specialty work: TPO, EPDM, modified bitumen, built-up, green roof systems, or a solar-ready assembly. If you’ve got a written estimate in hand, we’ll give you a free second opinion on it. Call (844) 951-4545 and a live person picks up, day or night.
How GAF Products Fail – and How We Fix Them
GAF makes good roofing products. But Summerlin’s heat, monsoon-season wind, and the hard afternoon sun off the Red Rock foothills work on them in specific ways, and we see the same GAF failure patterns year after year.
- GAF EverGuard TPO membrane, heat-weld seams: the factory seam is only as good as the weld. In Summerlin attics that regularly run well past 140°F, a weld that looked fine on install day can pucker and pull loose within a few seasons. We re-weld and probe every seam, not just the failed one.
- GAF EverGuard TPO, fastener back-out: mechanical fasteners backing out of the deck plate let the membrane balloon in monsoon gusts off the Spring Mountains. The membrane isn’t the culprit – the fastening pattern is. We pull and re-set fasteners at the correct spacing and add stress plates where the wind load demands it.
- GAF Ruberoid modified bitumen, granule loss and blistering: on low-slope sections that get direct western sun, we see the cap sheet blister where the base sheet wasn’t fully bedded. It looks like simple wear until you peel a corner and find trapped moisture underneath. We open the blister, dry the deck, and re-cap it correct.
- GAF EverGuard EPDM, seam shrinkage: EPDM seams pull at the seams over time as the membrane relaxes in heat. A seam that’s shrunk back half an inch is a water path. We spline and re-seal to spec, or replace the sheet if the edge has gone too far.
- GAF built-up and green roof assemblies, flashing at penetrations: most of the leaks we find on Summerlin flat and garden roofs aren’t in the membrane field – they’re at vents, drains, and the roof-to-wall tie-in where flashing was never dressed properly. We flash those points to the job, not to a guess.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Our GAF Specialty Roofing Process
Here’s how a GAF job actually goes, from the call to the cleanup.
- 1
The call and the visit. You call, a real person answers, and we set a time. No call centers, no forms that go nowhere.
- 2
Diagnostics. We go up and look. I’ll show you the deck photos before we talk money. We measure in squares and confirm the count so you can compare it against any other bid.
- 3
Parts decision. Where a GAF OEM part is the right call, we use GAF. On hardware and smaller accessories we use a quality aftermarket where it performs as well and keeps the warranty intact, and we tell you which is which and why.
- 4
The work. Bill and his crew do the job, with the right fastening pattern and flashing detail for Summerlin’s wind and heat.
- 5
The test. We check seams, probe welds, and water-test where it makes sense before we call it done.
- 6
The guarantee and cleanup. Every job comes with our written 90-Day Done Right Promise. We leave the yard clean, and one call brings Bill back if something isn’t right.
What GAF Specialty Roofing Costs in Summerlin
Here are the ranges we see on actual Summerlin jobs. Your numbers depend on the size of the roof, the assembly, and how much deck repair is underneath.
- TPO re-weld and seam repair: $450 to $1,200 per section, depending on how many seams need attention.
- Fastener re-set and stress-plate install: $600 to $1,800 for a typical low-slope section.
- Modified bitumen blister repair and re-cap: $700 to $2,200 per area.
- EPDM seam re-seal or sheet replacement: $500 to $2,500 depending on extent.
- Flashing and penetration re-detail (built-up, green roof): $400 to $1,500 per penetration cluster.
- Full specialty replacement (TPO, modified bitumen, built-up): priced per square – we’ll give you the square count and a written line-item on the estimate.
What moves the price is deck condition, how accessible the roof is, and whether we find wet insulation under the failed area. We pull the estimate before we start, and the number doesn’t change once we’re up there. Call (844) 951-4545 for a free estimate – it’s free, and you’ll know the number before anyone touches your roof.
See the difference
Before
After
Before
After
Before
AfterWhy Summerlin Homeowners Call Shepherd & Sons Roofing Summerlin for GAF Work
We’ve been at the same address since 1996 – over 29 years, same shop, same name on the truck, same owner on the roof. Bill Shepherd’s name and license number are published, and he answers his own phone. If something goes wrong, you know exactly who to call.
Every roster job – including GAF specialty work – is backed by the written 90-Day Done Right Promise. Our technicians have up to 30 years of experience, and Bill’s own sons are on the roof with him. We also install and service Owens Corning and CertainTeed products when that’s the right fit. Call (844) 951-4545 – a live person answers 24/7, including nights and weekends after a storm.
FAQs
Yes – GAF’s manufacturer warranty stays in place as long as the repair is done to GAF’s published installation standards, which is exactly how we work. Our 90-Day Done Right Promise covers the labor on top of that. We can’t speak for the manufacturer’s decision on any specific claim, but we document the job so the warranty is supported. Call (844) 951-4545 for a free second opinion on your estimate.
Both, and we tell you which and why. OEM GAF membrane, flashing, and seam materials go where the warranty and performance depend on it. Quality aftermarket hardware goes where it performs equally well and keeps the assembly intact. You’ll see the breakdown on the written estimate.
Most GAF specialty repairs in Summerlin are repairable. Mem brane seam failures, fastener back-out, and flashing leaks are typically fixable without a full replacement. Full replacement makes sense when the deck is wet across a large area or the insulation has failed. We’ll show you the deck photos so you can see it yourself.
We schedule promptly and a live person answers the phone 24/7 so you’re never waiting on a voicemail. For planned repairs, we set a date that works. For storm damage, call right away. There’s no trip charge inside our own county.
Yes. We work on GAF EverGuard TPO, EverGuard EPDM, Ruberoid modified bitumen, and built-up and green roof assemblies, along with solar-ready roof systems. Call (844) 951-4545 and describe what you’ve got – we’ll tell you what we’re seeing.
Get Your Free Estimate
If you’ve got a GAF specialty roof in Summerlin that needs a real look, call (844) 951-4545. A live person answers 24/7, and we’ll come out, show you the deck photos, and give you a written line-item estimate before anyone touches your roof. Ask anyone on your street – the name on the truck is the name on the license.
Written by the team at Shepherd & Sons Roofing Summerlin, serving Summerlin and nearby areas.